PC-case feature trends have changed a bit in the eight years that Fractal Design has been putting its signature crumpled-mesh faces on classic mid-tower cases. (The aesthetic crumpling is easier to see in photos of the shinier black finish, such as the Meshify 2 we reviewed in 2021.) This latest version adds an air deflector at the front of the power supply shroud to force a bit more airflow past your hot graphics card.

This Ambience Pro RGB variant’s feature set, as noted, has a USB-based ARGB controller, as well as lighting around the front face, along the bottom of the left side panel’s window, and on the three fans. Buyers willing to forgo most of the lit-up bling can get the basic “RGB” version with just the fan lighting for $159.99, and those willing to give up even that helping of ARGB can get the base “TG” version for $139.99. Our sample was in white; all three models are also available in black, and buyers who yearn for further simplification will find an additional “Solid” variant sold exclusively in black, with a painted steel panel on the left side in place of the window.

Fractal Design has merged the headphone and microphone jacks of previous versions into a single four-pole connector on the Meshify 3. This connector functions as a normal headphone jack when one is plugged in; the extra pole serves the monaural microphone of a combined headset plug. Fractal also ditched the reset button of previous cases, but kept the twin USB 3 Type-A and a single Type-C port. And, this time around, the lighted power-on indicator ring that surrounds the power button is ARGB.

(Credit: Thomas Soderstrom)

Though the mesh that covers the face and top panel could potentially filter out some inbound dust, the only part of the Meshify 3 that’s explicitly designed as a dust trap is under the power supply’s air inlet. Sliding out from the case’s side, it’s partially disguised as a portion of the rear case foot.

(Credit: Thomas Soderstrom)

The Meshify 3’s back panel features a pattern of vent slots spaced to allow a fan to be screwed directly into the slots. Also back here are surface-mounted PCI Express expansion-card slots with replaceable covers, a plastic screw-tab cover with a built-in push tab at the bottom to ease its removal, and a removable power supply bracket that’s secured with two large knurled screws. Power supply insertion is through the case’s rear panel; the design lacks the space to slide in the power supply from the side.

(Credit: Thomas Soderstrom)

Both side panels are secured at the top with snaps, and Fractal Design added a pair of tabs to make that task a little easier. Those tabs also have screw holes, enabling you to further secure your side panels against accidental removal.

A nylon pull tab at the center of the top panel’s back edge serves a similar function. To release that panel and lift it off, you must first slide it back a quarter inch or so.

(Credit: Thomas Soderstrom)

The front ARGB fans have 140mm frames, but there’s too little space behind them to mount a 420mm-format radiator vertically. That’s because radiator end caps tend to extend the total size by around 40mm (give or take 6mm).

(Credit: Thomas Soderstrom)

On the other hand, those really motivated to place a radiator behind the front panel’s fans will find that a 360mm-format unit will work, but only by removing the 140mm fans and flipping the fan-mount brackets over. (They are visible in the image below.) Fractal Design’s brilliance shines through with these very basic sheet-metal brackets that flip to support either 120mm or 140mm fans without hindering airflow.

(Credit: Thomas Soderstrom)

The top panel is fully removable to ease radiator installation and removal, but it does not benefit from the front panel’s design wizardry. While its straight-edged brackets will cover a portion of the fan’s blades when fans are mounted directly on them, its 330mm-plus of length is sufficient to support every 280mm-format radiator we can think of.

Also, notice the removable cable shroud running up and down the case near the front. It is adjustable to fit motherboards up to 10.9 inches deep. That is less than the 13-inch max depth of Extended ATX, but it’s still sufficient to fit the slightly oversized enthusiast-class motherboard models that sometimes still get called EATX.

(Credit: Thomas Soderstrom)

The lower front fan’s air deflector is removable and sits far enough above the case’s floor to be used in conjunction with a pair of 2.5-inch drive bays hidden beneath it. (We don’t even want to think about how we’d manage the cables in that configuration, however.)

We removed the cable shroud for a clearer shot of this area. Keen observers might note the mounting slot for its lower edge at the top of the photo.

(Credit: Thomas Soderstrom)

Two drive trays, three push-in cable clips, and the ARGB controller are all found behind the motherboard tray. The card bracket’s removable covers and the removable power supply bracket are shown in the image below detached and in front of the case, and the photo also shows the gap beneath the removable front fan duct into which some builders may want to install a pair of 2.5-inch drives.

Get Our Best Stories!

All the Latest Tech, Tested by Our Experts

Sign up for the Lab Report newsletter to receive PCMag’s latest product reviews, buying advice, and insights.

By clicking Sign Me Up, you confirm you are 16+ and agree to our Terms of Use and Privacy Policy.

Thanks for signing up!

Your subscription has been confirmed. Keep an eye on your inbox!

(Credit: Thomas Soderstrom)

More drive storage is visible here on the back of the motherboard tray. Configured from the factory to hold two 3.5-inch drives, these brackets on the back of the motherboard tray can be repositioned to hold four 2.5-inch drives instead.

(Credit: Thomas Soderstrom)

Held in place by a hook-and-loop Velcro-style strap, the included ARGB controller has USB and PWM input on the top, proprietary combination connectors on the side, and an old-fashioned SATA power connector on its bottom to power it up.

(Credit: Thomas Soderstrom)

Note that Fractal designed special outer shells on the proprietary ARGB/PWM combo connectors. This design is to prevent them from being mistakenly connected to anything USB Type-C, from which they appear to borrow their form. As with several others, this photo again shows the 10mm gap between the bottom panel’s 2.5-inch drive mounts and the underside of the front fan’s air guide.

(Credit: Thomas Soderstrom)

As for the controller box itself, here’s a shot of the connectors that we couldn’t see in the ARGB controller’s previous photos, including the SATA power inlet.

(Credit: Thomas Soderstrom)

Of the two output cables we did see, one is for the case’s chain of fans, and the other is for this version of the case’s “Ambience Pro” lighting. Four telescoping contact pins allow the front panel’s portion to separate easily from the rest of that latter cable without an awkward tether.

(Credit: Thomas Soderstrom)